Ctrl+Z opens the QTC window for the station being worked, which is the key N1MM
puts it on, and the window is laid out the way N1MM lays it out: the header,
ten lines of time, callsign and serial number, an Agn and a Cfm button beside
each, Clear, Close and Cancel underneath, and the same colours — green for a
line that will be saved, red for one still empty, yellow for one that cannot be
read. Enter and Tab move forward and space moves within a line, so a line can be
walked while listening to it.
Sending, the lines are filled from the log and cannot be edited: the contacts
not reported to anybody yet, oldest first, never the station being worked, and
never past the ten any station may have. The rule for what has been reported is
N1MM's — a contact counts as reported when a QTC row carries its call and the
serial we sent it — so the pair is kept in the row the way N1MM keeps it.
Which way traffic goes is not the operator's choice on CW and SSB: Europe
receives and the rest of the world sends. On RTTY it goes both ways, and there
the window carries a switch. That is the one piece of the workflow that is ours
rather than N1MM's, which toggles a QTC mode outside the window instead.
Nothing here transmits. N1MM sends the lines on CW and RTTY and plays recorded
voice messages on SSB; we have no QTC message templates, no voice keyer and no
digital window, so Agn, Cfm and RX Ready move the cursor and the operator sends
by hand.
Running it caught what the tests could not: focus set in the constructor does
not stick, so the first thing typed into a freshly opened window was dropped and
every field after it took the value of the one before.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Ctrl+B calls CQ on one radio, and when that message has gone out, moves to the
other and calls there. The keyboard, the entry window and the SO2R box follow
each turn. N1MM calls this dueling CQs and puts it on the same key.
The turn is taken when the keyer says the message has ended, not when a timer
guesses it has. So MessageSender grew a Finished event and a ReportsCompletion
flag, and both keyers fill them in: cwdaemon answers the <ESC>h reply request
that now goes out in front of every message, and a WinKeyer clears the busy bit
in the status bytes it sends of its own accord. The status-byte reading is in
WinkeyerStatus, away from the serial port, because that is the half that can be
tested without a keyer on the desk. A keyer that reports nothing refuses to
start alternating CQ rather than keying the second radio over the first.
AlternatingCq itself takes the keyer, a callback that calls CQ on a radio, the
gap and a wait function, so the alternation is tested without sleeping. The gap
is in Config ▸ Keyer and messages and will not go below 100 ms, which is N1MM's
floor too: an SO2R box works relays.
docs/keying.md writes down why cwdaemon does the timing and we do not. N1MM
keys DTR itself with a coarse sleep, a busy-wait and a margin that grows every
time the sleep overshoots, and it raises the thread to TIME_CRITICAL for the
length of the message. The busy-wait ports to Linux; the priority does not,
without CAP_SYS_NICE, and a garbage collection mid-element is audible. A direct
serial keyer stays a reasonable third option, to be taken knowingly.
Running it against a fake daemon that takes 1.5 seconds to play a message: six
CQs went out back to back and the keyboard moved between the two entry windows
each time. Escape stopped it, let the message in flight finish, and started
nothing further.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
N1MM's format, so a file published for a contest is read as it is: # comments,
!!Order!! naming the columns of the lines after it, semicolons in preference to
commas so user text can hold a comma, and a default column order for a file
that names none. The directives that change what is stored are acted on;
!!Order!! can appear again part way through, because these files are usually
several files stuck together.
Leaving the callsign box fills what the file knows into the exchange boxes that
are still empty. A box with something in it is left alone: what the station
actually sends beats what somebody published months ago. The zone comes from
the CqZone or the ITUZone column depending on which the contest asks for, and a
file with no Sect falls back to State.
The check window's two missing columns are in. History lists matching calls
from the file. Exchange is not about callsigns at all: it offers the values the
exchange box with the cursor in it can hold, which is what N1MM's exchange pane
does — it searches the contest's list of valid exchanges, not the log.
CheckCandidate.Call is now Text, because an exchange value is not a call.
The section-validating directives are read and passed over rather than acted
on. Acting on them means holding N1MM's section lists and its rules about
retired sections, and getting that wrong throws away good data.
Running it caught what the unit tests could not: the exchange was filled and
scored but the boxes on screen still looked empty, because nothing resynced
them.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
LoggingSession mixed two things: the contest, which one station has one of,
and what the operator is typing, which belongs to a radio. It is now
ContestSession and RadioPosition. Two positions share one log, one score and
one run of serial numbers, so a station worked on radio 1 is a dupe on radio 2.
Frequency, mode, split, what is typed and whether you are running belong to
each radio on its own.
A second radio opens a second entry window. It has no menu of its own: it is
another view of the same contest, not another program. Only the window for
radio 1 opens the database and the connections.
Ctrl+Tab moves the operator to the other radio and the keyboard follows.
Ctrl+Shift+Tab puts both radios in the headphones.
OtrspBox speaks OTRSP to an SO2R box over a serial port: TX1/TX2 for the key,
RX1/RX2 and RX1S for the headphones, AUXnnn for an output line. It follows the
active radio, and every message points the box at this radio before keying, so
a message cannot go out of the radio the operator has just left. A command that
would change nothing is not sent, because the box works relays; N1MM does the
same. The box takes a Stream, so what it sends is tested without a serial port.
Still missing: alternating CQ, and voice keying on the second radio.
Looked at under Xvfb with two fake radios, one of them split: both windows up,
radio 1 showing 14008.00 into 14020.0, radio 2 on 14030.00, Ctrl+Tab moving the
keyboard between them.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Split. RadioState carries a transmit frequency, zero meaning the radio
transmits where it listens, so split is not a second flag that can disagree
with it. The contact stores it in N1MM's QSX column, the entry window shows
14008.00 followed by the transmit frequency, and the bandmap draws a red bar
there. SetSplitAsync sets the frequency before turning split on, or a radio
last split somewhere else transmits there.
Every command now goes out with a + in front, asking rigctld for its extended
answer: named fields ended by an RPRT line. The raw answer is bare values with
no terminator, so the client had to know how many lines each command returns —
there was a `command == "m"` special case for the one that returns two. Add a
third such command and get the count wrong once, and every later answer is read
against the wrong command for the rest of the session. RigctldReply parses the
extended form and is tested on its own.
A radio that cannot do split answers RPRT -11. That is an answer, not a broken
connection, so the frequency and mode it did report still count.
Two radios. Settings hold a list rather than one host and port, with the single
radio an older settings file holds carried into it. Both radios are read and
both show on the bandmap, the active one green and the other orange, but only
the active one drives the entry window: the second radio moving must not drag
the operator off the station being worked. Ctrl+Tab swaps, and a contact
records which radio made it.
This is not a full two-radio operating position — no second entry window, no
alternating CQ, no audio switching. It is two radios read and logged correctly.
Tested against a stand-in for rigctld over a real socket, and looked at under
Xvfb with two fake radios, one of them split.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The old client read the socket with a StreamReader, so the option negotiation a
node sends on connect landed in the text as control bytes and made a mess of
the first lines. TelnetStream now answers it: it agrees to ECHO and
SUPPRESS-GO-AHEAD, refuses everything else, swallows subnegotiations, and
tracks what it already answered so the two ends do not reply to each other for
ever. A command split across two reads is still understood, because a socket
hands over whatever has turned up rather than whole messages.
LineAssembler keeps the tail that has no line ending yet. Nodes write their
login prompt as "login: " with nothing after it, so the old ReadLineAsync sat
waiting for a line that never came and only got through because the greeting
happened to mention a matching word.
Login now follows N1MM: it looks for LOGON, ENTER CALL, LOG IN and the rest,
and sends the callsign anyway after ten seconds if no prompt turns up. A
password is sent when the node asks for one and the operator configured one.
The commands go out after that, not straight after the call. A connection that
has heard nothing for four minutes gets a blank line so the node does not drop
it as idle.
The old prompt check matched "call" anywhere in a line, which any spot comment
could trigger.
SendSpotAsync sends the node's dx command. Alt+P, or Edit / Spot It, spots the
call being typed at the current frequency, or the last contact logged when
nothing is typed, and puts it on our own bandmap without waiting for it to come
back round from the node.
The spot parser now takes a line with no colon after the spotter, and finds the
time when DXSpider has put the spotter's grid after it.
The cluster tests run over a real socket against a node fake that sends the
negotiation, the prompt and spot lines.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Ctrl+Y from the entry window, or Enter on a row in the log, opens the whole
contact in one dialog. It reaches the fields the log has no column for: QSX
frequency, name, QTH, comment, grid, power, radio number, run position, and the
country and WPX prefixes. Previous and Next walk the log without closing and
offer to save first.
The dialog checks values through the same QsoEditor the log columns use, so a
zone the contest will not take is refused the same way in both places.
QsoEdit now names the field that was refused, so the dialog can put the cursor
back in the right box, and QsoEditor.ApplyAll changes several fields at once.
Points and the multiplier flags are shown but not editable. They are worked out
from the rules every time the log changes, so a typed value would be lost on
the next edit. N1MM lets you type them; we do not, rather than offering a box
that does nothing.
A contact's own country prefix now wins over the country file when scoring.
Without this, correcting the country in the dialog would change what the log
shows and what Cabrillo says, but not the score.
LoggingSession.Update now broadcasts the change like Edit does, so a contact
saved from the dialog reaches the other stations.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The function keys send through cwdaemon or a WinKeyer, with N1MM's message
macros. Escape stops sending.
Settings are read with the reflection serializer rather than a generated one:
the generated one hands back null for every property the file leaves out
instead of the value the property is declared with, which crashed the program
the first time a new setting was added.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The entry window types contacts and colours them as they are typed; the log,
check, bandmap, score and packet windows read the same session. Contacts are
shared with the other stations of a multi-operator entry in N1MM's contact
message, so an N1MM station on the same network sees them too.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
erikbrockoandClaude Opus 5
ErikandClaude Opus 5